Made in USA
The Embedded Solutions Experts
cPCIBPMC3U32
Install PMC into 3U cPCI
cPCIBPMC3U32 Description
- No Software Required - transparent bridge
- 32 bit PCI operation, 33 or 66 MHz Clock, Universal voltage [3.3V or 5V on PCI bus]
- PMC position with aligned cPCI and PMC bezels
- LC Filtered 5V and 3.3V
- 3V or 5V PMC PCI VIO selection
- Voltage measured with LED indicators
- Cooling Fan option
- Rear IO option with matched length impedance controlled routes
- 3U 4HP
- Industrial Temperature standard
- 1 year warranty standard. Extended warranty available.
- ROHS and Standard processing available
Note: cPCIBPMC3U32 is the replacement for cPCIBPMC3U64ET. The 64 bit bridges are EOL. This version is a 32 bit cPCI implementation. The design is industrial temperature. Filtering, power distribution, PMC location have been retained. The rear IO is now routed with controlled impedance, and matched length.
cPCIBPMC3U32 is a 3U 4HP PMC adapter for cPCI. One PMC position is provided with a 32 bit interface for both the PMC and the cPCI backplane. User programmable VIO on the PMC side of the bridge. High capacity mini-planes with filtering for 3.3 and 5V.
A related product,, "cPCIBPMC6UET" is a 6U 4HP version with two PMC positions. The 6U version has both PMC IO connectors routed with equal length traces to J3 and J5. A PIM Carrier is available for the 6U model to support rear panel IO.
cPCIBPMC3U32 ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. cPCIBPMC3U32 has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32 width with 33/ 66 MHz bus operation. cPCIBPMC3U32 can be installed into a 64 bit system without the RIO option in place. The PMC bezel connector is mounted though the cPCI mounting bracket. cPCIBPMC3U32 is an extended temperature design. -40C to +85C standard. Conformal Coating is an option.
PCI VIO is interconnected to the primary side of the bridge. The secondary side of the bridge has programmable VIO allowing 5V PMCs to be used in 3V systems and vice-versa. The voltage select pins are not installed on cPCIBPMC3U32. The bridge will automatically adapt to the PCI bus reference voltage. Many PMCs are "universal" and can work with 3.3 or 5V cPCI backplanes.
Power is routed from the cPCI to PMC connectors with mini-planes each of which is rated for more than the maximum PMC draw. 3.3, 5, VIO, +12, -12
cPCIBPMC3U32 has low internal power dissipation. The dissipation is a function of the frequency and load from the installed PMC. For PMCs with higher power dissipation or for use in chassis with low airflow the Zero Slot fan option is recommended. The fans does not require an added slot and provides about 5 CFM of air movement.
With 3U cPCI, J2 has two definitions - in a 64 bit PCI implementation J2 has the upper A/D and control signals, and in a 32 bit PCI implementation J2 has the rear panel IO. cPCIBPMC3U32 has the Pn4/Jn4 IO from the PMC connected to J2.
If your project requires 64 bit PCI operation cPCI2PMC-64 can be ordered ito provide a passive 64 bit implementation.
cPCIBPMC3U32 is a 3U 4HP PMC adapter for cPCI. One PMC position is provided with a 32 bit interface for both the PMC and the cPCI backplane. User programmable VIO on the PMC side of the bridge. High capacity mini-planes with filtering for 3.3 and 5V.
A related product,, "cPCIBPMC6UET" is a 6U 4HP version with two PMC positions. The 6U version has both PMC IO connectors routed with equal length traces to J3 and J5. A PIM Carrier is available for the 6U model to support rear panel IO.
cPCIBPMC3U32 ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. cPCIBPMC3U32 has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32 width with 33/ 66 MHz bus operation. cPCIBPMC3U32 can be installed into a 64 bit system without the RIO option in place. The PMC bezel connector is mounted though the cPCI mounting bracket. cPCIBPMC3U32 is an extended temperature design. -40C to +85C standard. Conformal Coating is an option.
PCI VIO is interconnected to the primary side of the bridge. The secondary side of the bridge has programmable VIO allowing 5V PMCs to be used in 3V systems and vice-versa. The voltage select pins are not installed on cPCIBPMC3U32. The bridge will automatically adapt to the PCI bus reference voltage. Many PMCs are "universal" and can work with 3.3 or 5V cPCI backplanes.
Power is routed from the cPCI to PMC connectors with mini-planes each of which is rated for more than the maximum PMC draw. 3.3, 5, VIO, +12, -12
cPCIBPMC3U32 has low internal power dissipation. The dissipation is a function of the frequency and load from the installed PMC. For PMCs with higher power dissipation or for use in chassis with low airflow the Zero Slot fan option is recommended. The fans does not require an added slot and provides about 5 CFM of air movement.
With 3U cPCI, J2 has two definitions - in a 64 bit PCI implementation J2 has the upper A/D and control signals, and in a 32 bit PCI implementation J2 has the rear panel IO. cPCIBPMC3U32 has the Pn4/Jn4 IO from the PMC connected to J2.
If your project requires 64 bit PCI operation cPCI2PMC-64 can be ordered ito provide a passive 64 bit implementation.
cPCIBPMC3U32 Features
Size
3U 4HP
PMC compatible slots
one position.
Clocks
cPCI bus can operate at 66 or 33 MHz. The PMC must be 66 MHz capable for 66 MHz operation to work properly. User switch to allow or disable 66 MHz. operation. Auto detection via M66EN signal.
Conversion
All standard accesses - Target Write, Target Read, DMA write, DMA read, interrupts etc. are supported on both sides of the bridge.
Cable interface
PMC Bezel IO defined by installed PMC through cPCI bezel, and optional Rear [J2] IO supported
Software Interface
Transparent Bridge with no requirement for programming. PMC register definitions as defined by installed hardware. No software set-up required by cPCIBPMC3U32.
Interrupts
INTA, B, C, D routed to cPCI connector from PMC.
Power
5, 3.3, +12, -12V, and VIO supplied to PMC. 5V and 3.3V are supported with LC filtering. Oversized planes used for power distribution.
VIO
Bridge primary PCI IO Voltage is set by the PCI backplane. Secondary side VIO is programmable by the user.
LEDs
5V, 3.3V, 12V, -12V LEDs illuminated when within tolerance.
Reliability
TBD Hours Bellcore SR332
Export Classification
EAR99, HTS:8537.10.9050
cPCIBPMC3U32 Benefits
Speed
The bridge allows for isolation and for differing clock rates on the cPCI backplane and the PMC. Tested with the Dynamic Engineering PMC-Parallel-TTL-GPIO design using Target Read, Target Write, DMA read and DMA write, plus interrupts. -RIO models additionally tested with external loop-back. With the bridge design all PCI and cPCI specifications are met - in particular the impedance and length of the PCI traces.
Price
System level cost is best when reasonably priced reliable hardware is used and NRE minimized. With cPCIBPMC3U32, PMC can be utilized in a cPCI system. Please check the current per item pricing with the storefront. Orders can be placed via the on-line ordering system or via phone / email PO order systems.
Ease of Use
cPCIBPMC3U32 is easy to use. The transparent bridge does not require programming. Drivers for the PMC will see through the bridge and access the installed PMC. Please download the manual.
Availability
We work to keep the base design of cPCIBPMC3U32 in stock. Dynamic Engineering has in house manufacturing capabilities for short lead times on larger orders, or special requirements.
PMC Specification Compatibility
cPCIBPMC3U32 is PMC compliant per the VITA specification. All Dynamic Engineering PMC Modules are compatible with cPCIBPMC3U32. All other PMC Modules which are compliant with the VITA specification can be expected to work.
cPCI Compatibility
cPCIBPMC3U32 is a PCI compliant device. cPCIBPMC3U32 can be expected to work in any cPCI compliant backplane. Rear IO modules will need to be installed into backplane positions with RIO supported [not 64 bit PCI]. ESD strip is incorporated into the design. EMC gasket
Part Number: cPCIBPMC3U32
Ordering Options
- cPCIBPMC3U32 Standard board - Industrial Temperature components, PMC postion, Bezel IO
-
Add any of the following build options after the PN as shown:
- -FAN( ) Need additional cooling? Order cPCIBPMC3U32-FAN( ) for a pre-installed 12V 5.2CFM fan to maximize cooling and functionality of your card. The fan has been tested with high wattage PrPMC devices. Valid Fan options include: standard and Rz for low profile fans with fan direction toward PMC or pulling air from the PMC [R]. An additional option is to use standard height fans with more LFM. 8 CFM fans are available as rear mount only (add -FANR to PN for this option)
- -RIO cPCIBPMC3U32 standard model with J2 and Jn4 installed for PMC Rear IO through carrier
- -VIO3 Force to PCI 3.3V on secondary side - normally switch selectable between 3.3 and 5V PCI voltage reference.
- -JTAG add optional JTAG header
- -CC Option to add Conformal Coating
- -ROHS Use ROHS processing. Standard processing is "leaded"
cPCIBPMC3U32 Drivers
Software Support for cPCIBPMC3U32 is not required.
Please see the Driver manuals for the installed XMC.
Dynamice Engineering XMC modules include software support - usually Linux and Windows. Please refer to the product page for the specific PMC module for manuals and supported OS.
Please see the Driver manuals for the installed XMC.
Dynamice Engineering XMC modules include software support - usually Linux and Windows. Please refer to the product page for the specific PMC module for manuals and supported OS.
cPCIBPMC3U32 Manuals
Click on the link to Download selected manuals in PDF format.
Download the cPCIBPMC3U32 Statement of volatility in PDF format.
Download the cPCIBPMC3U32 HW Manual in PDF format.
Download the cPCIBPMC3U32 Statement of volatility in PDF format.
Download the cPCIBPMC3U32 HW Manual in PDF format.